Code: Select all
[email protected]:~ $ sudo startx xauth: file /root/.Xauthority does not exist X.Org X Server 1.17.2 Release Date: 2015-06-16 X Protocol Version 11, Revision 0 Build Operating System: Linux 3.8.11-2-ARCH armv7l Raspbian Current Operating System: Linux raspberrypi 4.1.17-v7+ #838 SMP Tue Feb 9 13:15:09 GMT 2016 armv7l Kernel command line: [email protected] dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1680 bcm2708_fb.fbheight=1050 bcm2709.boardrev=0xa21041 bcm2709.serial=0x4c1669a0 smsc95xx.macaddr=B8:27:EB:16:69:A0 bcm2708_fb.fbswap=1 bcm2709.uart_clock=3000000 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait Build Date: 11 January 2016 01:32:44PM xorg-server 2:1.17.2-1+rpi1 (http://www.debian.org/support) Current version of pixman: 0.33.3 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.1.log", Time: Sun Feb 14 20:24:18 2016 (==) Using system config directory "/usr/share/X11/xorg.conf.d" The XKEYBOARD keymap compiler (xkbcomp) reports: > Warning: Type "ONE_LEVEL" has 1 levels, but <RALT> has 2 symbols > Ignoring extra symbols Errors from xkbcomp are not fatal to the X server (EE) glamor0: GL error: FBO incomplete: driver marked FBO as incomplete [-1]
Most people here will be unaware of Eric's blog and so on, so here is a place where people can post any issues they find. They will make their way back to Eric.derhass wrote:I'm not sure what kinds of bugs are expected to be reported here. Thing is, the wiki page for the VC4 driver https://dri.freedesktop.org/wiki/VC4/ already mentions conformance testing using piglet and also list a lot of stuff which is not working / incomplete. I could report a few GL issues I've encountered, but these are most likely already known, according to these sources.
Code: Select all
dtparam=audio=on start_x=1 gpu_mem=128 core_freq=250 sdram_freq=400 over_voltage=0 display_rotate=1 dtoverlay=vc4-kms-v3d
The firmware is no longer in charge of graphics with this driver, so config.txt settings will not work.havenotfear wrote:After activating the OpenGL Driver I am unable to rotate my display. Not sure if this is a bug or perhaps that setting has been change somewhere. Here is the relevant section in /boot/config.txt
Welcome Eric,anholt wrote:I've enabled issue tracking on my two github repos and propagated a bunch of these bugs there.
This is caused by an interaction between the GTK theme and the new driver; I've seen it in a couple of other cases. The new driver exposes the "client side decoration" features of the theme, which are otherwise not shown.levelcrow wrote:Hey, I hope I'm not too late to report something. I don't know how to use issue tracking on Github, so perhaps someone on the forums could help me out.
After enabling the OpenGL drivers, a black border has appeared when using Files - the file explorer based on Nautilus. The black border is always present no matter what and if there is a window behind it. It is not present when the OpenGL driver is disabled. I've attached a picture of the black border.
The same happens on my on RPI3, especially with Midnight Commander running in LXterminal - when resizing - system freeze is almost instantaneous.jamesh wrote:With drivers enabled, resizing LXterminal window results in either a massive delay or perhaps lockup.
1. Absolutely no audio ever through VNC.agor wrote:UPDATE:
First of all, omxplayer does not have any problems, it plays 1920x1080 flawlessly, my bad sorry about that.
And it is a x11vnc issue, with pi connected to my monitor through hdmi can see video and hear audio, but the vnc client does not display anything...
My guess is that i need to setup fbcp?
Any hints about this would be greatly appreciated.