Case for PiFace Digital

[killor]

Today I received my Piface PCB and I am making a new box for this new union.
It is a first test, not the final, because I did have the CASE before the new PCB physically and I must set some measures of the windows to make it look better
and any piece cause the buttons to access from outside the box.

Piface box

Piface_box1.jpg (62.77 KiB) Viewed 6357 times

Pi face box

Piface_box2.jpg (59.82 KiB) Viewed 6357 times

Piface digital BOX

Piface_box3.jpg (59.06 KiB) Viewed 6357 times

The overall dimensions are
40mm high x 68mm wide x 98mm long

These days, I finish the details and I will have ready for sale on eBay and Amazon, if anyone is interested in them.

[killor]

Last night, I was doing a case in of birch plywood to accommodate the RPI and PiFACE.

RPIFace box

Piface_box5.jpg (60.09 KiB) Viewed 6124 times

Raspberry pi face box

Piface_box7.jpg (52.81 KiB) Viewed 6124 times

I made a plywood buttons to access the keypad inside without opening the top.

Raspberry PI face case

Piface_box9.jpg (51.86 KiB) Viewed 6124 times

[waterman480]

Ordered my acrylic case on EBay yesterday - can't wait

[dan3008]

love the plywood buttons

[killor]

This is my last case for Raspberry and Piface made ​​of clear acrylic.

Raspberry PiFace acrylic case

piface01.jpg (55.59 KiB) Viewed 5115 times

I added a piece of acrylic to transmit light from the LEDs to the top.


Now also accept Bitcoins (BTC) to sell. on Bitmit web site.

[beruic]

It's beautifull in wood.

[killor]

It's beautifull in wood.

And more resistant to shocks.
Less electrostatic charge.
Since the grain is always different in some way, each case is unique.
100% biodegradables.

[killor]

I made a new piece for the bottom of the case.
Now the cases is adapted for VESA Mounting Interface Standard (MIS) or colloquially as VESA mount.

VESA MIS-D 100mm x 100mm or 75mm x 75mm

Now we just put the M4 screws and voila!

Piface enclosure with VESA botton

Piface_vesa.jpg (62.66 KiB) Viewed 3711 times

enclosure Raspberry pi .Adapter for PiFace board and Vesa mount

Piface_vesa2.jpg (61.04 KiB) Viewed 3704 times

Raspberry Piface plywood case with Vesa mount

Piface_vesa3.jpg (61.8 KiB) Viewed 3704 times

Soon will be available on AMAZON. B00BM4YP2C

[killor]

Hi

I designed a new enclosure model adapted to the new versions of boards
Raspberry Pi 2 and PiFace Digital 2.


Birch ply is made from laminations of birch veneer. It is light but strong, among the strongest and most dimensionally-stable plywoods.


Made of birch plywood this case keeps the Pi secure, has a hinged top for connector access, and even has little feet cut into the sides so that it stands up above your desk.



You can use all of the connectors on the edges of the Pi: HDMI, Audio/Video, microSD slot, micro USB power, Ethernet and the 4 USB ports.
There's also a cut out to allow a 40-pin IDC cable to the GPIO breakout pins on the Pi and pass it though the case and 2 rectangular openings for PiFACE board ports.
For more advanced hacking, the enclosure is designed so that you can lift or remove the top piece and plug any sort of cables you wish into the breakouts in the middle.



The case is airy enough that no additional vents or cooling is required - we tested the enclosed Pi over a 24 hour period at full load with no significant increase in temperature.

Sales on ETSY https://goo.gl/MEFZTO and eBay sites...