aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Thu Nov 24, 2016 7:58 pm

Hey there,
here's another special aspect ratio display connected to the RPi:
Sharp LQ092B5DW01.jpg
Sharp LQ092B5DW01.jpg (12.67 KiB) Viewed 6525 times
https://youtu.be/isqD8UGTBB0
Will post config settings later here (although part of the story is in this thread viewtopic.php?p=1010869#p1010869 )

Project XXX
Posts: 15
Joined: Thu Oct 02, 2014 9:36 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Fri Nov 25, 2016 8:20 am

Nice to see that you find the right timing settings, looking forward to recieve the PCB and play with it.

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Fri Nov 25, 2016 4:24 pm

So, here's the timing used for the demo video:

Code: Select all

# ---------------------------------------------
# For use with Sharp LQ092B5DW01 module only
# rev. 16/11/2016
# ---------------------------------------------

# For more options and information see
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
# Some settings may impact device functionality. See link above for details
# enable 24-bit DPI interface
dtoverlay=dpi24

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1

# ---------------------------------------------
# Overscan Information
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
# --------------------------------------------- 
#overscan_left=0
#overscan_right=0
#overscan_top=0
#overscan_bottom=0

# uncomment to force a console size. By default it will be display's size minus
# overscan.
# Portrait or Landscape Setting - only uncomment one block at a time
# Portrait-1 ( normal )
display_rotate=0
framebuffer_width=960
framebuffer_height=160

# Landscape-2 ( upside down )
#display_rotate=2
#framebuffer_width=960
#framebuffer_height=160

#Portrait-1 ( right side up )
#display_rotate=1
#framebuffer_width=160
#framebuffer_height=960

# Portrait-2 ( left side up )
#display_rotate=3
#framebuffer_width=160
#framebuffer_height=960

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# ---------------------------------------------
# Enable DPI
# --------------------------------------------- 
enable_dpi_lcd=1

# ---------------------------------------------
# Make DPI default output
# ---------------------------------------------
display_default_lcd=1

# ---------------------------------------------
# custom HDMI mode
# https://www.raspberrypi.org/forums/viewtopic.php?p=613926#p613926
# https://www.raspberrypi.org/forums/viewtopic.php?f=29&t=24679
# ---------------------------------------------
dpi_group=2
dpi_mode=87

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=900
gpu_mem=194

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=off
#dtparam=i2s=on
dtparam=spi=off

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on
 ---------------------------------------------
# DPI output format definitions
# https://www.raspberrypi.org/forums/viewtopic.php?p=628061#p628061
# DPI structure: https://www.raspberrypi.org/forums/viewtopic.php?p=617719#p617719
# ---------------------------------------------
# output_format:
#   1: DPI_OUTPUT_FORMAT_9BIT_666
#   2: DPI_OUTPUT_FORMAT_16BIT_565_CFG1
#   3: DPI_OUTPUT_FORMAT_16BIT_565_CFG2
#   4: DPI_OUTPUT_FORMAT_16BIT_565_CFG3
#   5: DPI_OUTPUT_FORMAT_18BIT_666_CFG1
#   6: DPI_OUTPUT_FORMAT_18BIT_666_CFG2
#   7: DPI_OUTPUT_FORMAT_24BIT_888
#
# rgb_order:
#   1: DPI_RGB_ORDER_RGB
#   2: DPI_RGB_ORDER_BGR
#   3: DPI_RGB_ORDER_GRB
#   4: DPI_RGB_ORDER_BRG
#
# output_enable_mode:
#   0: DPI_OUTPUT_ENABLE_MODE_DATA_VALID
#   1: DPI_OUTPUT_ENABLE_MODE_COMBINED_SYNCS
#
# invert_pixel_clock:
#   0: RGB Data changes on rising edge and is stable at falling edge
#   1: RGB Data changes on falling edge and is stable at rising edge
#
# hsync polarity: 
#   0: default for HDMI mode
#   1: inverted
#
# vsync polarity:
#   0: default for HDMI mode
#   1: inverted
#
# output_enable_polarity:
#   0: default for HDMI mode
#   1: inverted
#
# hsync phase:
#   0: rising edge
#   1: falling edge
#
# vsync phase:
#   0: rising edge
#   1: falling edge
#
# output_enable phase:
#   0: rising edge
#   1: falling edge
# ---------------------------------------------
# output_enable_mode/vphase/output_enable_phase = 1
dpi_output_format=262421

# ---------------------------------------------
# HDMI timing definitions
#https://www.raspberrypi.org/forums/viewtopic.php?f=29&t=24679
# ---------------------------------------------
# hdmi_timings= <h_active_pixels>
#		  LCD module horizontal resolution
#
#               <h_sync_polarity>
# 		  0: active low
#		  1: active high
#
#               <h_front_porch> 
#		<h_sync_pulse>
#		<h_back_porch>
#		<v_active_lines>
#		  LCD module vertical resolution
#
#		<v_sync_polarity>
# 		  0: active low
#		  1: active high
#
#		<v_front_porch>
#		<v_sync_pulse>
#		<v_back_porch>
#
#		<v_sync_offset_a>
#		<v_sync_offset_b>
#		<pixel_rep>
#
#		<frame_rate>
#		  screen refrech rate (50/60Hz supported only!)#
#
#		<interlaced>
#
#		<pixel_freq>
#		  calculates as: <h_active_pixels> * <v_active_lines> * <frame_rate>
#
#		<aspect_ratio>
#		  HDMI_ASPECT_4_3 = 1
#		  HDMI_ASPECT_14_9 = 2
#		  HDMI_ASPECT_16_9 = 3
#		  HDMI_ASPECT_5_4 = 4
#		  HDMI_ASPECT_16_10 = 5
#		  HDMI_ASPECT_15_9 = 6
#		  HDMI_ASPECT_21_9 = 7
#		  HDMI_ASPECT_64_27 = 8
# ---------------------------------------------
#hdmi_timing for LQ092B5DW01 configuration notes
#h_active_pixels = 960
#h_sync_polarity = 1
#h_front_porch = 2
#h_sync_pulse = 6
#h_back_porch = 244
#v_active_lines = 160
#v_sync_polarity = 1
#v_front_porch = 0
#v_sync_pulse = 10
#v_back_porch = 40
#v_sync_offset_a = 0
#v_sync_offset_b = 0
#pixel_rep = 0
#frame_rate = 60
#interlaces = 0
#pixel_freq = 32004000
#aspect_ratio = 8
# ---------------------------------------------
hdmi_timings=960 1 2 6 244 160 1 0 10 40 0 0 0 60 0 32004000 8
Strange thing is that I need to operate the display at roughly double the max dot clock.
Forum user 'ait' shared below hdmi_timings

Code: Select all

hdmi_timings=960 1 2 8 242 160 1 0 10 40 0 0 0 60 0 15900000 8 
but since I don't know it's settings for dpi_output_format the display my displays are not working with this timing (15.9MHz dot clock is in spec btw).

So, in case some other users have such a display would be great if they can share their timing details :!:

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Wifi enabled backlight driver for LQ092B5DW01

Wed Jan 04, 2017 12:41 pm

Hi,
the LQ092B5DW01 TFT module has no integrated backlight driver. The backlight of the module is as below:
- 3 LED string white backlight @ typ. 18.5V
- 1 LED string red backlight @ typ. 12V
- contacts available on a 0.5mm pitch FPC connector

So, this module has three 'challanges': requires some tiny connector and two different voltages.

That's why I had the idea to make my own LED driver for this board with features like:
- only one supply voltage (12V) and using a cheap step-up DC/DC module (XL6009E1 http://www.banggood.com/XL6009-Step-Up- ... mds=search) to generate the 18.5 - 19V
- usable for other modules as well
- two independent LED driver for different voltages --> decided to use two On-Semi CAT4104 because they allow up to 25 V operation on LED pins, 4 channles with 175mA sink current each
- easy to control via PWM

Well ... PWM is an issue when using DPI interface, so I've added a ESP8266 wifi module! I'm running a simple web server on it which allows to adjust the brightness of each of the backlights.
WP_20170104_13_12_42_Smart.jpg
Wifi-enabled backlight driver for LQ092B5DW01
WP_20170104_13_12_42_Smart.jpg (54.9 KiB) Viewed 6092 times
WP_20170104_13_12_52_Smart.jpg
Wifi-enabled backlight driver for LQ092B5DW01 - top side with DC/DC and ESP8266 module (ESP12)
WP_20170104_13_12_52_Smart.jpg (63.44 KiB) Viewed 6092 times
WP_20170104_13_13_14_Smart.jpg
Wifi-enabled backlight driver for LQ092B5DW01 - bottom side with CAT4104 LED drivers
WP_20170104_13_13_14_Smart.jpg (57.34 KiB) Viewed 6092 times

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Red TFT module backlight

Thu Jan 05, 2017 1:31 pm

Here is what the module looks like when red backlight is used:
r100_w0.jpg
LQ092B5DW01 - red backlight set to 100%, white backlight off
r100_w0.jpg (63.77 KiB) Viewed 6004 times
r100_w10.jpg
LQ092B5DW01 - red backlight set to 100%, white backlight det to 10%
r100_w10.jpg (58.95 KiB) Viewed 6004 times

james-at-lo-tech
Posts: 45
Joined: Sat Oct 04, 2014 1:07 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Thu Jan 05, 2017 2:54 pm

Did you achieve concurrent output to this and the HDMI output via framebuffer device mapping somehow?

ait
Posts: 125
Joined: Sun Oct 30, 2011 6:51 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Thu Jan 05, 2017 2:57 pm

Here is what the module looks like when red backlight is used:
Aha, i never tried the red backlight.
Afaik the display was part of the BMW 7 Dashboard.
The red backlight was for the "Night Mode".
Last edited by ait on Thu Jan 05, 2017 4:20 pm, edited 1 time in total.

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Thu Jan 05, 2017 4:13 pm

ait wrote:
Here is what the module looks like when red backlight is used:
Aha, i never tried the red backlight.
Afaik was the display part of the BMW 7 Dashboard.
The red backlight was for the "Night Mode".
:idea: :!:
james-at-lo-tech wrote:Did you achieve concurrent output to this and the HDMI output via framebuffer device mapping somehow?
Also people claim that this should be possible - with some dedicated software like omxplayer i.e. (in general: software which supports output re-direction), I could never get any output on the HDMI interface when using DPI interface.
Due to the fact that the display connected to DPI interface is my main screen - means nothing is connected to HDMI - I never investigated this matter.

james-at-lo-tech
Posts: 45
Joined: Sat Oct 04, 2014 1:07 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Thu Jan 05, 2017 5:08 pm

Omxplayer works fine with DPI interface, but we need a framebuffer driver to create /Dev/fb1 for the non-primary display for it to be usable by lightdm.

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Thu Jan 05, 2017 5:54 pm

james-at-lo-tech wrote:Omxplayer works fine with DPI interface, but we need a framebuffer driver to create /Dev/fb1 for the non-primary display for it to be usable by lightdm.
I know that omxplayer works fine with DPI (as you can see from the video in the first post of this thread), but I never managed to get a second omxplayer instance playing to HDMI at the same time
If you know how to achieve this, let me know the commands and I will test.

User avatar
rpdom
Posts: 13564
Joined: Sun May 06, 2012 5:17 am
Location: Chelmsford, Essex, UK

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Thu Jan 05, 2017 7:39 pm

aBUGSworstnightmare wrote:I know that omxplayer works fine with DPI (as you can see from the video in the first post of this thread), but I never managed to get a second omxplayer instance playing to HDMI at the same time
If you know how to achieve this, let me know the commands and I will test.
I believe using omxplayer --display=5 will use the HDMI or Composite outputs, and --display=4 will use the DPI output. I've had simultaneous playback of different videos on HDMI and DPI via Gert's VGA board.

james-at-lo-tech
Posts: 45
Joined: Sat Oct 04, 2014 1:07 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Thu Jan 05, 2017 7:48 pm

In my testing,
  • To play on DPI device when desktop is on HDMI device: omxplayer --display 4 test.mp4
  • To play on HDMI device when desktop is on DPI device: omxplayer --display 5 test.mp4

NOOBS_2016
Posts: 5
Joined: Fri Dec 23, 2016 9:46 am

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Fri Jan 13, 2017 7:40 am

aBUGSworstnightmare wrote: So, in case some other users have such a display would be great if they can share their timing details :!:
hey,
i am working with the LQ092B5DW01-display too.
I have built my own PCB and connected it to the display. After booting the GUI appears, but the picture is flickering. I took your settings, but I think they are not working perfectly for my display.
Which parameters would you change to stop flicker?

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Fri Jan 13, 2017 5:36 pm

NOOBS_2016 wrote:
aBUGSworstnightmare wrote: So, in case some other users have such a display would be great if they can share their timing details :!:
hey,
i am working with the LQ092B5DW01-display too.
I have built my own PCB and connected it to the display. After booting the GUI appears, but the picture is flickering. I took your settings, but I think they are not working perfectly for my display.
Which parameters would you change to stop flicker?
how should I know what you call 'flicker'?
Post your config.txt, let us know which RPi you're using (zero, 3, ..) and I can test it and see flickering.
In case of Zero I recommend increasing GPU clock, above settings work on my Zero and Rpi 3.
And, which of the timings that I've posted are you using? Only the one with 32MHz is working

NOOBS_2016
Posts: 5
Joined: Fri Dec 23, 2016 9:46 am

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Sat Jan 14, 2017 1:53 pm

aBUGSworstnightmare wrote:

Code: Select all

# ---------------------------------------------

dpi_output_format=262421

hdmi_timings=960 1 2 6 244 160 1 0 10 40 0 0 0 60 0 32004000 8

I use this settings in my "config.txt" and use a RPi 3. On monday i will post my complete "config.txt" and can share a dropbox-link with a video of my display.
Last edited by NOOBS_2016 on Mon Jan 16, 2017 7:21 am, edited 1 time in total.

ait
Posts: 125
Joined: Sun Oct 30, 2011 6:51 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Sat Jan 14, 2017 2:04 pm

Hello,
my settings in config.txt where ("where" because i do not use the display at the moment):
dtoverlay=dpi24
framebuffer_width=960
framebuffer_height=160

enable_dpi_lcd=1
dpi_group=2
dpi_mode=87 # Hdmi CVT
display_default_lcd=1

hdmi_timings=960 1 2 8 242 160 1 0 10 40 0 0 0 60 0 15900000 8
i used it with pizero and raspbian lite

NOOBS_2016
Posts: 5
Joined: Fri Dec 23, 2016 9:46 am

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Mon Jan 16, 2017 7:29 am

the video:
https://www.dropbox.com/sh/h2g54xbu9zxg ... 1iDba?dl=0

my config.txt:

Code: Select all

# For more options and information see
# http://raspberry.org/documentation/configuration/config-txt.md
# Some settings may impact device functinality. See link above for details

# Uncomment if you get no picture on HDMI for a default "safe" mode
#hmid_safe=1

# Uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# Uncomment to force a HDMI mode rather than DVI. This can make audio work in DMT (computer monitor) modes
#hdmi_drive=2

# Uncomment to increase signal to HDMI, if you have interference, blanking or no display
#config_hdmi_boost=4

# Uncomment for composite PAL
#sdtv_mode=2

# Uncomment to overclock the arm. 700MHz is the default.
#arm_freq=800

##############################
# settings for sharp-display #
##############################

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=off
dtparam=spi=off

# GPIO set to ALT2-function for DPI
dtoverlay=dpi24

# Uncomment this if your display has a black border of unused pixels visible and your diplay can output without overscan
disable_overscan=1

# Uncomment to force a console size. By default it will be display's size minus overscan.
display_rotate=0
framebuffer_width=960
framebuffer_height=160

# DPI-output activate / configure
enable_dpi_lcd=1
display_default_lcd=1

# Uncomment to force a specific HDMI mode (this will force DPI)
dpi_group=2
dpi_mode=87

# Enable audio (loads snd_bcm2835)
dtparam_audio=on

dpi_output_format=262421
hdmi_timings=960 1 2 6 250 160 1 0 10 40 0 0 0 60 0 32001000 8

gpu_mem=194

#Additional overlays and parameters are documented /boot/overlays/README

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Mon Jan 16, 2017 6:55 pm

NOOBS_2016 wrote:the video:
https://www.dropbox.com/sh/h2g54xbu9zxg ... 1iDba?dl=0

my config.txt:

Code: Select all

# For more options and information see
# http://raspberry.org/documentation/configuration/config-txt.md
# Some settings may impact device functinality. See link above for details

# Uncomment if you get no picture on HDMI for a default "safe" mode
#hmid_safe=1

# Uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# Uncomment to force a HDMI mode rather than DVI. This can make audio work in DMT (computer monitor) modes
#hdmi_drive=2

# Uncomment to increase signal to HDMI, if you have interference, blanking or no display
#config_hdmi_boost=4

# Uncomment for composite PAL
#sdtv_mode=2

# Uncomment to overclock the arm. 700MHz is the default.
#arm_freq=800

##############################
# settings for sharp-display #
##############################

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=off
dtparam=spi=off

# GPIO set to ALT2-function for DPI
dtoverlay=dpi24

# Uncomment this if your display has a black border of unused pixels visible and your diplay can output without overscan
disable_overscan=1

# Uncomment to force a console size. By default it will be display's size minus overscan.
display_rotate=0
framebuffer_width=960
framebuffer_height=160

# DPI-output activate / configure
enable_dpi_lcd=1
display_default_lcd=1

# Uncomment to force a specific HDMI mode (this will force DPI)
dpi_group=2
dpi_mode=87

# Enable audio (loads snd_bcm2835)
dtparam_audio=on

dpi_output_format=262421
hdmi_timings=960 1 2 6 250 160 1 0 10 40 0 0 0 60 0 32001000 8

gpu_mem=194

#Additional overlays and parameters are documented /boot/overlays/README
Check your cable and/or interface board.
Tested your settings here, image is stable but shifted 6 pixel to the right.
detail.jpg
6pixel offset to the right
detail.jpg (19.06 KiB) Viewed 5280 times
full.jpg
NOOBS_2016 timing on my HW
full.jpg (29.92 KiB) Viewed 5281 times
EDIT: btw... display rotate command can be omitted

NOOBS_2016
Posts: 5
Joined: Fri Dec 23, 2016 9:46 am

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Tue Jan 17, 2017 9:25 am

Thank you for your help...now it is working fine :D
I forgot to connect all GND-pins of the display with all GND-pins of the RPi :roll:

But i have still a other frequency than you, with your frequency it is flickering.

My timing:

Code: Select all

hdmi_timings=960 1 2 6 244 160 1 0 10 40 0 0 0 60 0 32900000 8

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Wed Jan 18, 2017 8:32 am

Sounds like some crosstalking issues; good to hear you got it fixed.
I would not worry about driving frequency difference; as long as your picture is stable I would say 'mission completed'

NOOBS_2016
Posts: 5
Joined: Fri Dec 23, 2016 9:46 am

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Thu Jan 19, 2017 12:36 pm

I was interested which frequency for the CLK-signal is the lowest the RPi 3 is able to send out.
So i checked it with an oscilloscope and the result was 31,253,817 Hz.

I changed the frequency in the hdmi-timing-settings and it is still working fine

holo85
Posts: 2
Joined: Sat Feb 11, 2017 9:34 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Sat Feb 11, 2017 9:36 pm

These settings work for me:
hdmi_timings=960 0 20 50 70 160 0 10 10 30 0 0 0 60 0 19200000 1

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Sun Feb 12, 2017 8:17 am

holo85 wrote:These settings work for me:
hdmi_timings=960 0 20 50 70 160 0 10 10 30 0 0 0 60 0 19200000 1
Please post your 'dpi_output_format' number too.

Using mine (dpi_output_format=262421) results in the display being offset to the left.
timing.jpg
timing.jpg (37 KiB) Viewed 4744 times

holo85
Posts: 2
Joined: Sat Feb 11, 2017 9:34 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Sun Feb 12, 2017 9:45 am

Sry,

# sharp LQ092B5DW01 parameter
dtoverlay=dpi18

overscan_left=1
overscan_right=1
overscan_top=0
overscan_bottom=0

framebuffer_width=960
framebuffer_height=160

enable_dpi_lcd=1
display_default_lcd=1
dpi_group=2
dpi_mode=87
dpi_output_format=278549

hdmi_timings=960 0 20 50 70 160 0 10 10 30 0 0 0 60 0 19200000 1

aBUGSworstnightmare
Posts: 1212
Joined: Tue Jun 30, 2015 1:35 pm

Re: Sharp LQ092B5DW01 (960x160pixel TFT module) meets RPi3

Sun Feb 12, 2017 12:08 pm

holo85 wrote:Sry,

# sharp LQ092B5DW01 parameter
dtoverlay=dpi18

overscan_left=1
overscan_right=1
overscan_top=0
overscan_bottom=0

framebuffer_width=960
framebuffer_height=160

enable_dpi_lcd=1
display_default_lcd=1
dpi_group=2
dpi_mode=87
dpi_output_format=278549

hdmi_timings=960 0 20 50 70 160 0 10 10 30 0 0 0 60 0 19200000 1
Thanks for sharing! Works like a charm 8-) :!:

Return to “Other projects”