Radius
Posts: 4
Joined: Mon Feb 04, 2013 9:09 am

How to get work DVB T2 Hauppauge WinTV-HVR-935HD

Sun Oct 28, 2018 9:11 pm

Hi,
can someone help me, how to get the dual DVBT2 card to work on RPI3?

lsusb
ID 2040:b151 Hauppauge

I have found how to compile drivers for Ubuntu, but not for Raspbian.
http://www.hauppauge.com/pages/support/ ... x.html#ppa

There should be drivers:
https://github.com/b-rad-NDi/Ubuntu-med ... el-builder

In my case, I need to make these steps (download kernel 4.15)
https://www.raspberrypi.org/documentati ... uilding.md

then apply these patches?
https://github.com/b-rad-NDi/Ubuntu-med ... nic-4.15.0

How? Download them (where) and like this page says?
https://www.raspberrypi.org/documentati ... atching.md

cat 0001-Linuxtv.org-media-tree-sync-2018-04-30-04-20.patch | patch -p1
....
....
and thats all? No extra configuration?


Thanks for advice.
Radius
Last edited by Radius on Mon Oct 29, 2018 6:49 am, edited 1 time in total.

AltxF4
Posts: 3
Joined: Sun Oct 28, 2018 9:00 pm

Re: How to get work DVB T2 Hauppauge WinTV-HVR-935HD

Sun Oct 28, 2018 9:52 pm

I just wrote a post that should help you a bit, but it has not been approved yet.... depending on what your hardware is composed of. What is the output from dmesg?

Radius
Posts: 4
Joined: Mon Feb 04, 2013 9:09 am

Re: How to get work DVB T2 Hauppauge WinTV-HVR-935HD

Fri Nov 02, 2018 9:38 am

Hi,
nothing special:

[ 2.011500] usb 1-1.4: new high-speed USB device number 4 using dwc_otg
[ 2.144024] usb 1-1.4: New USB device found, idVendor=2040, idProduct=b151
[ 2.144035] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.144043] usb 1-1.4: Product: Hauppauge Device
[ 2.144052] usb 1-1.4: Manufacturer: Hauppauge
[ 2.144060] usb 1-1.4: SerialNumber: xxxxx

R.

walterav1984
Posts: 4
Joined: Tue Feb 14, 2017 8:31 am

Re: How to get work DVB T2 Hauppauge WinTV-HVR-935HD

Sun Nov 04, 2018 7:55 pm

Solution easier than you might think, the next raspbian release will have out of the box support for this tuner (except firmware if needed).

https://github.com/b-rad-NDi/Ubuntu-med ... -435699342

Instructions for RPI3
Start without your USB tuner attached and use a recent updated raspbian image and update your kernel to 4.19 with the following command:

Code: Select all

sudo apt-get update
sudo apt-get -y upgrade
sudo apt-get -y dist-upgrade
sudo BRANCH=next rpi-update #use capitals since command is case sensitive!

sudo apt-get -y install tvheadend #available in raspbian repo since DVB-t2 HAT ;-)

sudo reboot
#After finishing reboot type
dmesg
#insert your usb tuner
dmesg
#notice any thing about missing firmware.fw, google your firmware and download it
wget http://someadress/examplefirmware.fw
sudo cp examplefirmware.fw /lib/firmware/
sudo reboot

#enjoy your mainline hauppauge linux driver!


Return to “Media centres”