energenie

B.Goode

(Credits for the first 2 belong to energenie, who wrote the original script, I simply corrected it, and added the correct codes to add sockets 3 and 4 if you want 4 sockets controlled by a pi, as its impossible to find the code online via ...

StuckPI

... and if the temp is under the range it simply writes a file to the network smb server. Another pi monitors this server, and turns on and off those energenie sockets. (i know your not supposed to have 2 on an extension, but i discovered if they are paired to a different reciever they wont interfere, ...

StuckPI

... paired. Pi: Raspberry PI 2B+ Also tested on Raspberry PI 3. OS: Jessie Lite (update May 2016) Device: ENER002-2PI. Pre-requisites: gpi-gpio . energenie . Pi mote wired on jumper leads to T-Cobbler. (Credits for the first 2 belong to energenie, who wrote the original script, I simply corrected ...

B.Goode

... your ongoing interest and support. I was not the original poster in this thread, but this has prompted me to try out a PiMote control board and Energenie remote switch, something I had meant to do for ages. I can confirm that the web interface, and the energenie interface in its revised form, ...

penguintutor

I have now updated the code to use the GPIO Zero module instead of the Energenie module used previously. Also thanks to other updates to the Raspbian image and converting the startup to systemd the install is now slightly easier. Details are provided on my ...

penguintutor

... far? Also have you registered the Pi-Mote with the socket by using the on button after plugging in the socket? If you are looking to coding the Energenie plugs from within Python then the Energenie board has now been added to GPIO Zero which is at https://gpiozero.readthedocs.org/en/v1.2.0/api_boards.html#energenie ...

B.Goode

... you checked the installation and functioning of the PiMote controller and the pairing with the remote switches by running the demo code on the Energenie website, here: https://energenie4u.co.uk/catalogue/download_software/ENER002-2PI.py

Mercer

Hopefully this is allowed -- bump.

Mercer

I just got a Raspberry Pi 3 and have been having the most frustrating time. http://www.penguintutor.com/raspberrypi/pi-power I have been using this tutorial to get my Energie plugs working and I am not sure what is going wrong I have the RPi module plugged in on the side closest to the SD card, the ...

PiGraham

... Or Enegenie http://uk.farnell.com/productimages/standard/en_GB/2433437-40.jpg http://uk.farnell.com/energenie/ener314/rf-controller-board-for-raspberry/dp/2433437?CMP=ADV-CRUK-LF

theraspberryguy

Maybe try lighttpd and php for the webserver.
This can be run directly on the pi which is easier.
Energenie is good for home automation.

jh_dempsey

I checked the sockets using the remote I got with them. The sockets learn the codes for sockets 1 2 3 4 and All without a problem, so there is no problem with the sockets themselves

jrs301257

I have the same problem with a recently purchased Pi-Mote starter kit from Energenie. I'm using an early Raspberry Pi with Rev1 GPIO. I started by trying the ENER002-2PI.py programme from the Energenie website ( https://energenie4u.co.uk/catalogue/product/ENER002-2PI ...

StuckPI

I have energenie, this via a command line script turns on and off 2 wall sockets. I have installed apache2 on my raspberry pi I spent the last 8 hours and a pizza, (meat feast over priced but edible) And im now on a sugar rush ...

btidey

... socket to socket dupont lead. pi433.jpg With more money there is also a GPIO module that does the same thing. It is advertised for controlling Energenie sockets but I think the software could be replaced to control other 433MHz devices. https://energenie4u.co.uk/catalogue/product/ENER314

jh_dempsey

... to send signals through it. I have successfully used this with the codes from here: http://www.richud.com/wiki/FT232R_BitBang_433MHz_Energenie_Power_Socket to control one on my Energenie plug sockets. The above works for "socket 1" and the "all sockets" commands, but I can't get my ...

lucyrstone

... bit of a "proof of concept" about getting a Popcorn machine to work automatically when you logged into Netflix. We used a Raspberry Pi and an Energenie and some code from the internet to get it working ready for our presentation http://www.penguintutor.com/raspberrypi/pi-power . Sadly we didn't ...

AndiTails

... a few times, to send some commands to essentially switch the modem off and on again. I bought this Pi-controlled sockets from Amazon made by Energenie. Mine actually arrived with the more expensive controller board which actually needed some C coding rather than Python after a lot of head-scratching. ...

spegru

... - It's a dual relay but I am pretty certain it works the same way. I didn't get any success with the Pi so far (although I have got it controlling energenie mains power sockets using the pimote circuit board similar to this https://energenie4u.co.uk/catalogue/product/ENER002-2PI-RT) I want to be ...

planetf1

Is the pimote a reasonable start to work with lightwaveRF devices? Are there specs on the board's chips? I assume it's similar to getting a seperate 433 rx and tx.... But nicely packaged?

DougieLawson

... in PHP). It also needs the gpio utility from Drogon's WiringPi (which should be installed on a stock Raspbian system). To get it working with an energenie system you'll have to set more than one GPIO depending which button gets pressed. If you want me to do that please send me an energenie system ...

broo0ose

if the Pi is connected to the HDMI on the TV you can put it in and out of standby using the command tvservice .
There's also CEC which has more advanced control over HDMI on more modern TVs,

For full power control I'd recommend the Energenie add on.

Search this forum and you should find more info

DougieLawson

... webserver is going to be the easiest option at the moment. Making Apache2, Lighttpd or NGINX wiggle GPIO pins (in the pattern needed for the Energenie stuff) isn't something I can hack together for you on Xmas Eve. get pi-power installed with cd /home/pi git clone https://github.com/penguintutor/pi-power ...

Gorf

... True) # keep enabled for a period time.sleep(0.25) # Disable the modulator GPIO.output (22, False) GPIO.cleanup() It turns on all the sockets. The energenie routines aren't exactly faultless either. I've had to mess around with the K0-K3 inputs to arrive at combinations that work for all the plug ...

Gorf

... - as you can probably tell, I'm not an HTML developer, nor have I any knowledge of PHP or Python. I'm just getting started. The device I bought (energenie remote sockets) was supposed to come with code so you could be up-and-running out of the box. Unfortunately it doesn't work, so I'm having ...

Search found 246 matches: energenie

Re: Code for PAIRING Pi-mote Energenie 4 sockets

Home Automation Step 1

Code for PAIRING Pi-mote Energenie 4 sockets

Re: Energenie Wall plugs & Raspberry PI

Re: Energenie Wall plugs & Raspberry PI

Re: Energenie Wall plugs & Raspberry PI

Re: Energenie Wall plugs & Raspberry PI

Re: Energenie Wall plugs & Raspberry PI

Energenie Wall plugs & Raspberry PI

Re: 433MHz Rx module that plugs directly on GPIO pins?

Re: Home automation

Re: Energenie signal/code help

Re: Energenie signal/code help

Php and python.

Re: 433MHz Rx module that plugs directly on GPIO pins?

Energenie signal/code help

The Little BIG Awards

[Guide] Automated reboot of my Virgin Media modem

Re: controlling wireless relay with 433Mhz transmitter

Re: Pi-mote from Energenie

Re: How to run an executable from PHP

Re: Raspberry Pi to power on a TV

Re: Exec python script from HTML

Re: Exec python script from HTML

Re: Exec python script from HTML