Raspberry Pi Forums

nicksoph

The competence of a person to give advice, is not always best judged by their confidence.

nicksoph

WindZ wrote: on a raspberry pi 3 and then i turn the sd back on my raspi 0 w and it works

me too.

nicksoph

No Wireless Interfaces are found on a Rpi Zero W - If you can do anything at all with the internal wifi eg. on or off, this unlikely to apply. What happned- Installed 10.4.17 Jessie full from this site onto 16gb sd card and noticed fault as described above. (rinsed and repeated) same issue. Followed...

nicksoph

Thanks scruss,
I shall look up splines and see how far I get - many thanks

nicksoph

I have a set of x,y, z coordinates and want to plot a smooth line through them rather than just straight lines between and cant seem to find how. Does anybody know if this is possible in Mathematica. Any advice on how I might accheive this using something other than Mathematica would also be appreci...

nicksoph

knarfboy wrote:Is it possible, in a new board Revision, to connect FM antenna port of BCM 43438 +3.3 volts?

Not possible. The pin out for the antenna is in the center of the CPU and has not been routed out to the PCB because no method could be found without increasing the number of PCB layers required.

nicksoph

EDIT - FIXED Issue was with memory allocation split cpu/gpu : was set too low, must be at least 128Mb set aside for GPU Hi Nick, By any chance are you using a RPI v1 (256mb/512mb) device? A GPU memory split of 16MB works with the RPI v2 (1GB), this is what i used for testing the camera. Hi Dan - Us...

nicksoph

Hi fourdee, thanks for the fix but it seems that whilst the camera will take and save photo's the "Record Video Start" button is not functioning - its not greyed out but just never turns to Stop Video or saves any video. Not sure if Its me but did try to follow instructions (fresh install of V70 fro...

nicksoph

Just wanted to add a note here to say that I had a problem with the install that was solved with changing permissions on /etc/rc.local During the install process I noticed an error: When asked - "Do you want to enable Auto Start (y/n)", replying "y" brought up; ./RPi_Cam_Web_Interface_Installer.sh: ...

nicksoph

Hi Not sure if this is the place to post this - if not please redirect me and I will remove from here. Just installed Diet-Pi and the RPi Web Cam Interface that Diet pi has on its site onto a RPi2 without an USB stick and all works well except; cant seem to save the images or videos - the uconfig fi...

nicksoph

Just wanted to report back that this worked and to say thanks to you both.

nicksoph

Hi - thought that likely - maybe something to bear in mind for Pi 3?

nicksoph

Thanks for the advice klricks - I will do as you suggest.

nicksoph

Just a wish - If the distance between the holes for the posts was altered slightly they would fit Lego dimensions. The distance between the holes is currently 58mm x 49 mm if this were to be changed to 56 x 48 mm they would line up to an 8mm grid which might prove useful to those who like their plas...

nicksoph

Thanks Burngate - that is what I wanted to hear.
Really appreciate your help.

Many thanks.
nick

nicksoph

I think the problem may be to do with your IP addressing being set up as two networks with no bridging between them - ie your pi knows about both networks but hasnt been told how to pass info between them.
This might help;
http://superuser.com/questions/520172/w ... e-in-linux

nicksoph

Thanks Burngate your reply (looks to me as though it) answered my questions (both technical and philosophical) perfectly. One more question related to power which would remove the need for me to try and understand the schematics: Would applying power to PP2 connected to the 5v input, and PP5 to grou...

nicksoph

Hi I have a need to be able to feed power to a Raspberry Pi 2 from a socket that is on the same end as the USB/network ports. The intention is to have a custom case with an insulated microUSB socket sitting on the rear side of the PCB beneath the network port, with cables from this new microUSB port...

nicksoph

Thanks DeeJay
Code club looks to be promising.

nicksoph

I have been following the RPi for some time and have bought a couple along the way. I recently visited my cousin who is the head teacher at a primary school in the poorer bit of Islington in London and picked up on a conversation that I had had with her some months ago. The gist of that conversation...

nicksoph

Received my R.Pi today and just played with it for most of the day and just wanted to say thank you to those who have produced this very good thing.
nick

nicksoph

<t>I was struck by how many people have such a wide range of uses for the R.Pi and thought I would try and design a minimal case that might meet those diverse needs. What I eventually came up with was not a case but simply a board holder that held the board and made it easier to affix it to other th...

nicksoph

<t>Hi Abishur<br/> <br/> Im drawing a case idea out at the moment and am a bit concerned about the pcb height - I had been working on the idea that it was a 4 layer pcb which was .6mm thick - which Im sure I read on this site somewhere: If it is a 6 layer pcb might you know its thickness?<br/> <br/>...

nicksoph

Put this in another thread - cant see a way to upload full sized image if anyone can advise?

nicksoph

nicksoph said:

More importantly what is the smiley for a raspberry? -

Search found 27 matches

Re: [Pi Zero W]Wifi Device wlan0 not found at all

Re: [Pi Zero W]Wifi Device wlan0 not found at all

Re: Pi Zero W - No WiFi interfaces found

Re: Smooth lines in 3d

Smooth lines in 3d

Re: The Raspberry Pi 3 Model B Q&A thread

Re: Cam Control

Re: Cam Control

RPi Cam Web Interface - Install Perms Issue

Diet Pi - RPi Cam Web Intfce - No files

Re: Moving Power In Connector

Re: Move holes

Re: Moving Power In Connector

Move holes

Re: Moving Power In Connector

Re: Pi not answering on eth0 but OK on wlan0

Re: Moving Power In Connector

Moving Power In Connector

Re: Getting RPi started at a Junior School

Getting RPi started at a Junior School

Thanks

Re: The projects list. Look here for some ideas.

Re: Custom Case, Need 3D Models

Re: Raspberry Pi Wallpaper

Re: R-Pi Wallpapers