Go to advanced search

by RootKiiit
Fri Jun 12, 2020 7:11 pm
Forum: Networking and servers
Topic: Configure the RPi as a Local Network Access Point (wired and wireless)
Replies: 12
Views: 850

Re: Configure the RPi as a Local Network Access Point (wired and wireless)

I looked at the dnsmaq logs and noticed that only one IP address was being assigned per IP camera. But still, after checking the IP addresses on the network using nmap, there were multiple IPs per device. These extra IPs (the one that I didn't recognize from the dnsmasq logs) were still valid and I...
by RootKiiit
Thu Mar 26, 2020 5:51 pm
Forum: Other
Topic: Pi1B - alternative to Raspbian Lite?
Replies: 15
Views: 1444

Re: Pi1B - alternative to Raspbian Lite?

If you think its software related then you could test with an older copy of raspbian. You will find Jessie or Stretch lite versions here https://downloads.raspberrypi.org/raspbian_lite/images/ look at the versions with the following dates for the last version of each 2017-07-05 , 2019-04-09 Salud f...
by RootKiiit
Sat Oct 26, 2019 5:26 am
Forum: General discussion
Topic: Setting up a WiFi without graphical interface
Replies: 3
Views: 385

Re: Setting up a WiFi without graphical interface

Good morning, Tom! I was desided the some problem with the wpa_cli and with the next link: http://linux.die.net/man/8/wpa_supplicant
If You not had a IP-address, then make next steps:
1. sudo killall dhcpcd
2. sudo dhcpcd wlan0 start

P.S I used "sudo ifconfig -a" instead "ip a"
by RootKiiit
Mon Jul 16, 2018 1:46 pm
Forum: Beginners
Topic: Can I using wi-fi connect two pi's together without a hotspot?
Replies: 14
Views: 1683

Re: Can I using wi-fi connect two pi's together without a hotspot?

Can I program two pi so listen to a specific (but different) 168.100.???.??? adresss and have them communicate directly without having to go through a router or to install hotspot software? It seems like this should be possible. Can it be easily done? Is it just a matter of setting up a special lis...
by RootKiiit
Sun Feb 04, 2018 5:50 pm
Forum: Troubleshooting
Topic: Latest release Feb2018 corrupts LXDE
Replies: 25
Views: 3291

Re: Latest release Feb2018 corrupts LXDE

Good evening! I have a problems with the last update same too... I press Ctrl+Shift+F1 and was started raspi-config and than I was selected gui with authorization...
by RootKiiit
Wed Jan 31, 2018 7:47 pm
Forum: Русский
Topic: После загрузки черный экран
Replies: 11
Views: 5730

Re: После загрузки черный экран

После загрузки, при "чёрном экране" перейдите в первую консоль (Ctrl+Alt+F1) и оттуда запустите raspi-config. В нём установите пароль для входа и выберете гуёвый сеанс с авторизацией... Затем ребут и будет Вам ;) У меня открылась первая консоль... Можно просто попытаться запустить иксы оттуда... Не ...
by RootKiiit
Sat Jan 20, 2018 5:29 am
Forum: Русский
Topic: Требует авторизацию при входе
Replies: 3
Views: 5724

Re: Требует авторизацию при входе

Ставил разные системы - где-то было pi:pi, где-то pi:raspberry, pi:raspbian... На компе вставте карту в картридер, примонтируйте куда-нибудь, зайдите под chroot'ом и задайте пароль root'а: passwd root "your-password" (и ЗАПОМНИТЕ его!). Затем выйдете из chroot'а, отмонтируйте карту и переставте обра...
by RootKiiit
Mon Apr 07, 2014 2:24 pm
Forum: Other projects
Topic: Raspberry Pi Radio
Replies: 4
Views: 4186

Re: Raspberry Pi Radio

Hi, Gekko! I made your piRadio and I'm very glad - it´s best !!! I use PI32-TFT display from HwLevel and kernel 3.10.25. I use standalone mode only, and I want connect the DS1307 I2C digital clock. My display have touchscreen on a ADC7846 and 5 buttons and I want use its... Are You have a possible m...
by RootKiiit
Mon Dec 16, 2013 6:35 am
Forum: HATs and other add-ons
Topic: 2.8" TFT + Touch Shield Board v1 a/b/c
Replies: 383
Views: 227960

Re: 2.8" TFT + Touch Shield Board

Hardware... It is a possible... Display is HY28A-LCDB. I have a HDMI display is connected and I can get a 2 framebuffers - odd on HY28A-LCDB and even on a HDMI (ctrl-alt-F1, ctrl-alt-F3, ctrl-alt-F5 and ctrl-alt-F2, ctrl-alt-F4 etc) and I can startx both, and to switch between it...
by RootKiiit
Sun Dec 15, 2013 9:06 pm
Forum: HATs and other add-ons
Topic: 2.8" TFT + Touch Shield Board v1 a/b/c
Replies: 383
Views: 227960

Re: 2.8" TFT + Touch Shield Board

Hi, Texy ! I have HY28A-LCDB display and it working, but I can not make a touchscreen work. Step "sudo TSLIB_FBDEVICE=/dev/fb1 TSLIB_TSDEVICE=/dev/input/event2 ts_calibrate" from a first post : – I had a freezy screen and I can out with a ctrl-alt-del keys only. I tested touchscreen with a LED on a ...

Go to advanced search