Go to advanced search

by tekim
Thu Sep 07, 2017 7:57 pm
Forum: General discussion
Topic: LAN Network Traffic
Replies: 4
Views: 2036

Re: LAN Network Traffic

Greetings,

A solution used in another post uses a RasPi as a router and logs the traffic. I have not tried this here is the url

http://blog.ronenb.com/2016/08/20/netwo ... /#more-146

Cheers,
by tekim
Mon Jan 23, 2017 5:05 pm
Forum: General discussion
Topic: LAN Network Traffic
Replies: 4
Views: 2036

Re: LAN Network Traffic

Greetings, I think you would need an old ethernet hub not a switch. The whole point of a switch is that all traffic is not available at all connections, only at the interface with the destination mac address. A hub allows all traffic on all sockets and as such forms a single collision domain and is ...
by tekim
Fri Nov 11, 2016 3:24 pm
Forum: General discussion
Topic: Pi Camera for solar viewing
Replies: 3
Views: 976

Re: Pi Camera for solar viewing

Greetings,

I am unable to answer your question and you maybe already aware of this website

http://www.qcuiag.org.uk/

but if not you may find it of interest.

Cheers
by tekim
Fri Jul 29, 2016 3:44 pm
Forum: Troubleshooting
Topic: What's the '/number' after static ip in dhcpcd.conf
Replies: 5
Views: 1890

Re: What's the '/number' after static ip in dhcpcd.conf

Greetings,

A less technical answer: The value after the slash defines the number of most significant ones in the subnet mask. So /24 is the same as writing FF.FF.FF.00

As always I maybe quite wrong.

Cheers
by tekim
Thu Jan 08, 2015 5:13 pm
Forum: Bare metal, Assembly language
Topic: Bare Metal SPI
Replies: 7
Views: 3786

Re: Bare Metal SPI

Writing code for driving SPI or I2C hardware can be trouble some if no diagnostic hardware is available and as I have only produced such code for PIC devices the following hints may not be of use. If so please ignore this post. I found the most useful fact in both SPI and I2C specifications was the ...
by tekim
Fri Nov 28, 2014 4:22 pm
Forum: Off topic discussion
Topic: If the RPi was made by Apple.....
Replies: 8
Views: 1636

Re: If the RPi was made by Apple.....

Greetings, It would be helpful if a version could be produced similar to a B+ but without sockets. The sockets being replace by header pins in the manner of GPIO. The sockets could be supplied mounted on a strip suitable for inclusion in a case, similar to the manner of a PC. Having sockets on more ...
by tekim
Sat Aug 30, 2014 1:53 pm
Forum: Beginners
Topic: Apache2 access log
Replies: 6
Views: 4377

Re: Apache2 access log

Greetings, Thanks for the %p parameter use, this was included in some of the log formating templates but not part of the template that was being used, sods law. Having added %p the log messages did show the 8080 port, it's nice to have proof. Port 8080 is shown in some listings as being a substitute...
by tekim
Sat Aug 30, 2014 1:42 pm
Forum: Beginners
Topic: Editing the Samba Config file
Replies: 5
Views: 1542

Re: Editing the Samba Config file

Greetings,

Does the "testparm" command not achieve a similar result?

testparm > smbclean.conf

or maybe

testparm -v > smbclean.conf
for all the default setting included.

Cheers,
by tekim
Mon Jun 16, 2014 11:27 pm
Forum: Beginners
Topic: Apache2 access log
Replies: 6
Views: 4377

Re: Apache2 access log

Greetings,

Thanks for the Apache2 log format parameter %p I have included this and will see what happens.
As pointed out previously port 8080 must be being used as the router is not thought to be faulty but
this will prove the point.

Cheers,

tekim
by tekim
Mon Jun 16, 2014 7:02 pm
Forum: Beginners
Topic: Apache2 access log
Replies: 6
Views: 4377

Re: Apache2 access log

Greetings, Thanks for your very rapid reply. I was hoping that Apache2 could be set to include the port number along with the IP address as recorded in the log file, my knowledge is very limited regarding the configuration of Apache2 all a bit 'try it and see'. On reflection maybe port 8080 was not ...
by tekim
Mon Jun 16, 2014 4:48 pm
Forum: Beginners
Topic: Apache2 access log
Replies: 6
Views: 4377

Apache2 access log

Greetings, The set-up:- Router forwarding port 8080 to RasPi Apache2 running on RasPi listens and will reply All working OK The RasPi is not, as far as I know running anything other than Apache2. O.S. is wheezy. However in the Apache2 access log file are messages similar to these:- 61.231.89.98 - - ...
by tekim
Mon Oct 15, 2012 3:43 pm
Forum: Off topic discussion
Topic: What is the LOWEST level language??
Replies: 33
Views: 9714

Re: What is the LOWEST level language??

Of course in any modern computer that is impossible, because all the logic is inside the computer chip, sealed inside plastic and implemented in a single piece of silicon. The above quote {rurwin} would not appear to be absolutely the case as this Celeron powered system loads a microcode patch on b...
by tekim
Sat Oct 06, 2012 3:21 pm
Forum: Off topic discussion
Topic: What is the LOWEST level language??
Replies: 33
Views: 9714

Re: What is the LOWEST level language??

A lower level programming would be microcode that's implemented on a risc design. This allows the target level machine code to be changed, on some designs there can be more than one (target level) running. This link is to a home designed and built computer. The website has a lot of detail. http://ww...

Go to advanced search