Go to advanced search

by Garu94
Thu Dec 12, 2019 7:19 pm
Forum: Beginners
Topic: Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?
Replies: 9
Views: 453

Re: Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?

Oh guys, I think I am *******k now, I just realized the cable wasn't fully plugged into the router.... Sorry for wasting your time so far. Now I have two different local IP, so I think this means the Pi is getting connection from both router and wifi. Given the lower metrics when running "route -n",...
by Garu94
Thu Dec 12, 2019 1:14 pm
Forum: Beginners
Topic: Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?
Replies: 9
Views: 453

Re: Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?

https://imgur.com/a/l8P9YJv
This is the output of dmesg, so it seems it is recognised properly as Ethernet gadget. From here, how should I use it? Am I missing something from config.txt or cmdline.txt in /boot partition maybe?
by Garu94
Thu Dec 12, 2019 9:44 am
Forum: Beginners
Topic: Pi Zero W performance limiting torrent download speed?
Replies: 3
Views: 192

Re: Pi Zero W performance limiting torrent download speed?

I am using deluge with deluge-console, and the only other thing running is dataplicty to connect remotely to raspberry.
https://imgur.com/a/BiQSdPg here is the output of htop ordered by memory usage.
Now I limited simultaneous downloads to one, and still have the same problem.
by Garu94
Wed Dec 11, 2019 2:48 pm
Forum: Beginners
Topic: Pi Zero W performance limiting torrent download speed?
Replies: 3
Views: 192

Pi Zero W performance limiting torrent download speed?

Hi, I have a Raspberry Pi Zero W setup with deluge to download torrents to an external NTFS HDD attached through a USB + Ethernet hub. Is it possible that the performance of the board are limiting download speed? Speed is usually under 10 KiB/s even with torrents with a lot of seeds, that on my desk...
by Garu94
Wed Dec 11, 2019 2:45 pm
Forum: Beginners
Topic: Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?
Replies: 9
Views: 453

Re: Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?

Yes, I did plug my cable in both the router and the adaptor. Is there anyway I need to configure on Raspberry Pi to "activate" this connection? As soon as I can, I will also try with the same port and cable I am using on my desktop to isolate the problem.
by Garu94
Tue Dec 10, 2019 10:20 am
Forum: Beginners
Topic: Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?
Replies: 9
Views: 453

Re: Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?

Hi, I tried but it didn't work. My ifconfig is showing this: eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 ether 00:00:10:02:61:c1 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrie...
by Garu94
Sat Dec 07, 2019 2:48 pm
Forum: Beginners
Topic: Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?
Replies: 9
Views: 453

Raspberry Pi Zero W: how to connect to ethernt with more priority than wifi?

Hi, I setup my Pi Zero W to connect automatically to wifi at boot, providing a wpa_supplicant.conf with my Wifi creadentials and editing config.txt and cmdline.txt in boot folder. So far everything works fine. Now, I bought a microUSB-Ethernet adaptor and, when I run ifconfig, I can see eth0 device....
by Garu94
Wed Dec 04, 2019 7:21 pm
Forum: Troubleshooting
Topic: Raspberry Pi Zero W can't start with USB stick connected
Replies: 0
Views: 77

Raspberry Pi Zero W can't start with USB stick connected

Hi everyone, I am trying to configure a torrent box with a Raspberry Pi Zero W, to get some hands-on before switching to a more powerful Raspberry Pi 4 if needed. I have two problems so far, but the stopping one is that it seems my Raspberry Pi Zero W with Raspbian Lite can't boot if USB stick is at...

Go to advanced search