Go to advanced search

by bmelum
Thu Aug 31, 2017 4:19 pm
Forum: Troubleshooting
Topic: STICKY: libmysqlclient18 has no installation candidate
Replies: 25
Views: 21622

Re: libmysqlclient18 has no installation candidate

Solved! Download from here https://packages.debian.org/wheezy/armhf/libmysqlclient18/download the package then install it via sudo dpkg --install libmysqlclient18 and then reinstall php5-mysql via apt-get apt-get install php5-mysql now misqli is installed cheers This solves my problem! I have a rea...
by bmelum
Fri Jul 24, 2015 10:28 pm
Forum: Troubleshooting
Topic: RPi 2: Problem getting WiFi-dongle to connect (Edimax)
Replies: 1
Views: 424

RPi 2: Problem getting WiFi-dongle to connect (Edimax)

Hello! I have bought an Edimax EW-7811Un, and have been trying to connect to my WiFi at home. I have read lots of different tutorials and tried different code, but I just cannot seem to get it working. I have checked that the dongle is connecting correctly with the command "lsusb" and found that it ...
by bmelum
Thu Jul 23, 2015 8:37 pm
Forum: Troubleshooting
Topic: RPi 2: Boot problem after using GPIO-connector
Replies: 8
Views: 941

Re: RPi 2: Boot problem after using GPIO-connector

Depends on what was connected where. For example: Arduino 5V supply --> Pi 3v3 supply = toasted Pi Arduino 5V output from a pin --> Pi gpio = fried Pi pin, potentially fried Pi processor (SOC) etc. If a fresh Raspbian image won't boot, you need a new Pi. Yes, you could have easily damaged your Pi b...
by bmelum
Tue Jul 21, 2015 11:53 pm
Forum: Troubleshooting
Topic: RPi 2: Boot problem after using GPIO-connector
Replies: 8
Views: 941

Re: RPi 2: Boot problem after using GPIO-connector

RPi GPIOs are not 5 volt tolerant. What do you mean? I hooked the 5V-pin from the GPIO to the Arduino, but it did not get 5 volts from any external component. I am a beginner at this, could you please explain a bit broader? :) Not all of the 40 pins on the header are GPIO. There are two 5V power pi...
by bmelum
Tue Jul 21, 2015 11:06 pm
Forum: Troubleshooting
Topic: RPi 2: Boot problem after using GPIO-connector
Replies: 8
Views: 941

Re: RPi 2: Boot problem after using GPIO-connector

drgeoff wrote:RPi GPIOs are not 5 volt tolerant.
What do you mean? I hooked the 5V-pin from the GPIO to the Arduino, but it did not get 5 volts from any external component.
I am a beginner at this, could you please explain a bit broader? :)
by bmelum
Tue Jul 21, 2015 11:04 pm
Forum: Troubleshooting
Topic: RPi 2: Boot problem after using GPIO-connector
Replies: 8
Views: 941

Re: RPi 2: Boot problem after using GPIO-connector

mikronauts wrote:Yes, you could have easily damaged your Pi by connecting the wrong things to the GPIO connector.

Depends on what - and how - you hooked up to the Pi's GPIO connector.
Do you think it is possible to boot the RPi anyway, just not being able to use the GPIO connector?
by bmelum
Tue Jul 21, 2015 7:01 pm
Forum: Troubleshooting
Topic: RPi 2: Boot problem after using GPIO-connector
Replies: 8
Views: 941

RPi 2: Boot problem after using GPIO-connector

Hello! I bought my RPi 2 a couple days ago, together with an Arduino L298N-module. I connected the RPi to the Arduino and then to a motor for a project I am doing. This worked all fine yesterday with no problems. Today I booted my RPi 2, and got this message: "sh: can't access tty; job control turne...

Go to advanced search