Go to advanced search

by bleep42
Wed Sep 25, 2019 2:40 pm
Forum: General discussion
Topic: Pi4 as Desktop computer
Replies: 245
Views: 20935

Re: Pi4 as Desktop computer

Go for a physical switch on a GPIO and use the [gpio27=0] conditional in config.txt to switch between the configurations. It's a useful little trick that I've been doing when testing out new kernels. If it doesn't boot then flick the switch to get back to a known good system, update the dodgy kerne...
by bleep42
Wed Sep 25, 2019 1:48 pm
Forum: General discussion
Topic: Pi4 as Desktop computer
Replies: 245
Views: 20935

Re: Pi4 as Desktop computer

And as far as overclocking, I consider myself lucky to have found at least one limit. AND - I am prepared to have to replace the Pi 4 if I kill it. And I do NOT plan to whine and complain and beg for warranty replacement i do! Some GIMP operations. Now all I probably should do do is write a little ...
by bleep42
Wed Sep 25, 2019 12:23 pm
Forum: General discussion
Topic: Pi4 as Desktop computer
Replies: 245
Views: 20935

Re: Pi4 as Desktop computer

It is able to run about everything fine at 2 GHz with over_voltage=5/6 and official power supply. Just not this. It shows the PMIC is a tight fit when not even 1.75 GHz works. [Citation needed]. Which SOCs are these? It was mentioned here in the forums somwhere that 2 GHz is the limit for the A72 a...
by bleep42
Wed Sep 25, 2019 11:25 am
Forum: General discussion
Topic: Pi4 as Desktop computer
Replies: 245
Views: 20935

Re: Pi4 as Desktop computer

I tried to reproduce this under a full 64 bits distro and unfortunately i can. The entire system just dies immediately as soon as it renders the preview image. There is not even a message about this in journalctl as far as i can see. This is pretty disappointing that we can't even get stable overcl...
by bleep42
Sun Sep 22, 2019 2:26 pm
Forum: Troubleshooting
Topic: Raspberry Pi 4 temperature
Replies: 558
Views: 161165

Re: Raspberry Pi 4 temperature

Being inaccurate is ok (just) , blatant lying is unacceptable. You clearly know very little about the Pi. 1. Not been around for 8 years. 2. Always had HDMI. 3. Unless you work for either Pi or Broadcom, your suggestions were probably not even noticed. If indeed you actually made them. And I'm pret...
by bleep42
Tue Sep 10, 2019 12:10 pm
Forum: General discussion
Topic: Pi 4 - full specification of VideoCore 6
Replies: 74
Views: 10737

Re: Pi 4 - full specification of VideoCore 6

No, nope. The correct theoretical performance of the GPUs is as follows: VideoCore IV @ 250MHz: 250 [MHz] x 3 [slice] x 4 [qpu/slice] x 4 [processor] x 2 [op/clock] = 24 Gflop/s VideoCore IV @ 300MHz: 300 [MHz] x 3 [slice] x 4 [qpu/slice] x 4 [processor] x 2 [op/clock] = 28.8 Gflop/s VideoCore VI @...
by bleep42
Mon Sep 09, 2019 4:09 pm
Forum: Troubleshooting
Topic: VLI firmware v2.0 - powersaving features enabled
Replies: 67
Views: 8241

Re: VLI firmware v2.0 - powersaving features enabled

Tested and working fine on a Pi4 with 64-bit raspbian kernel and hibrid boot using USB3 SSD.
Temperature is the same as the previous (updated) firmware 0137a8.
All good, thanks. :-)
Regards, Kevin.
by bleep42
Fri Aug 23, 2019 1:47 pm
Forum: Gentoo
Topic: Bootable 64-bit Gentoo image for the RPi4 released (Xfce4 desktop)
Replies: 36
Views: 6190

Re: Bootable 64-bit Gentoo image for the RPi4 released (Xfce4 desktop)

Hi Sakaki, Fantastic achievement, well done :-) Considering the amount of racket that certain people are making about the 'new Pi4' not having a 64bit operating system, I was expecting your thread to be heaving with activity, (echo) clearly they don't really care, can't be bothered, are just being a...
by bleep42
Fri Aug 09, 2019 1:23 pm
Forum: General discussion
Topic: Pi4 as Desktop computer
Replies: 245
Views: 20935

Re: Pi4 as Desktop computer

For USB boot, use a SD card to redirect boot to the USB device you want to boot from. The only difference from native USB boot is you need a SD with with just bootcode.bin on it and some config. I have seen a few posts suggesting this as the current solution for USB booting but does this actually w...
by bleep42
Sun Jul 28, 2019 1:19 pm
Forum: Graphics, sound and multimedia
Topic: [UPDATE] Kodi 18.4 Leia for Raspberry Pi 4
Replies: 164
Views: 32132

Re: Kodi 18.3 Leia for Raspberry Pi 4

Doesn't sound as though the screen you are using is giving the correct CEC info to the Pi, my Pi always knows what the standard resolution of the display I have connected is. Check your screen has CEC enabled or search the forums for forcing a particular resolution, or start another thread, as this ...
by bleep42
Sun Jul 28, 2019 10:04 am
Forum: Graphics, sound and multimedia
Topic: [UPDATE] Kodi 18.4 Leia for Raspberry Pi 4
Replies: 164
Views: 32132

Re: Kodi 18.3 Leia for Raspberry Pi 4

Hi, I used your advice about setting Display refresh rate to 'on start/stop' and set up the highest resolution in Kodi to 4096 x 2160. On other side my Raspbian resolution stayed on 1920x1080, 60.00Hz. Not sure if Raspbian buster resolution means something but this one fits nicely to my TV screen, ...
by bleep42
Sat Jul 27, 2019 3:24 pm
Forum: Graphics, sound and multimedia
Topic: [UPDATE] Kodi 18.4 Leia for Raspberry Pi 4
Replies: 164
Views: 32132

Re: Kodi 18.3 Leia for Raspberry Pi 4

Sorry you replied while I was editing my previous reply, I was wrong, and was correcting it, the Standard Kodi install uses 320M for GPU. Ok I have now connected it up to my main 4K TV, before I was playing a 4K source, through a standard hi res monitor. my TV is [email protected] as standard. I have t...
by bleep42
Sat Jul 27, 2019 1:50 pm
Forum: Graphics, sound and multimedia
Topic: [UPDATE] Kodi 18.4 Leia for Raspberry Pi 4
Replies: 164
Views: 32132

Re: Kodi 18.3 Leia for Raspberry Pi 4

For me 4k is not working very well. I tried following resolutions in Kodi under settup: 3840 x 2160, 30Hz and 4096 x 2160, 30Hz. Audio seems to work fine but not in the sync. with picture, probably because picture is stuttering big time, not watchable at all. Video used was not 4k but 1280 x 720 vi...
by bleep42
Sat Jul 27, 2019 1:46 pm
Forum: Graphics, sound and multimedia
Topic: [UPDATE] Kodi 18.4 Leia for Raspberry Pi 4
Replies: 164
Views: 32132

Re: Kodi 18.3 Leia for Raspberry Pi 4

For me 4k is not working very well. I tried following resolutions in Kodi under settup: 3840 x 2160, 30Hz and 4096 x 2160, 30Hz. Audio seems to work fine but not in the sync. with picture, probably because picture is stuttering big time, not watchable at all. Video used was not 4k but 1280 x 720 vi...
by bleep42
Sat Jul 27, 2019 9:52 am
Forum: Graphics, sound and multimedia
Topic: [UPDATE] Kodi 18.4 Leia for Raspberry Pi 4
Replies: 164
Views: 32132

Re: Kodi 18.3 Leia for Raspberry Pi 4

Hi Marvin, ;-) I've installed your Kodi on my Pi4, working great, I've tried to stress it by playing 4K HEVC (h265) & it didn't even work up a sweat, about 10% CPU usage, processor not getting above 60C. Thank you for providing this build, with any luck someone will put it in the official repository...
by bleep42
Wed Jul 17, 2019 8:34 am
Forum: Other projects
Topic: PiCrust4 (new improved)
Replies: 5
Views: 902

Re: PiCrust4 (new improved)

love this, looking at a similar project but with some more "open areas" for HW plugins experiments etc. I know you talked about a screen and having the driver specially programmed. 1) could you post the companys name that did it? 2) have you looked into a more generally accessible screen? I know Im...
by bleep42
Mon Jul 08, 2019 2:44 pm
Forum: General discussion
Topic: Pi4 as Desktop computer
Replies: 245
Views: 20935

Re: Pi4 as Desktop computer

Here is one!
Details can be found here:- https://www.raspberrypi.org/forums/view ... 1&t=244515
PiCrustss.jpg
Paspberry Pi4 Desktop
PiCrustss.jpg (100.64 KiB) Viewed 1226 times
PiCrustRears.jpg
Paspberry Pi4 Desktop connectors
PiCrustRears.jpg (92.7 KiB) Viewed 1226 times
by bleep42
Wed Jul 03, 2019 10:28 am
Forum: Other projects
Topic: PiCrust4 (new improved)
Replies: 5
Views: 902

PiCrust4 (new improved)

PiCrustss.jpg PiCrustFillings.jpg Hi Pi People, :-) A few years ago, I built the above 'Lap top' now that we have a Pi with extra OOmmph and the Foundation say it's good enough for a lap top, I have re fitted it with a Pi4 and called it a PiCrust. ;-) Original post is here https://www.raspberrypi.o...
by bleep42
Wed Aug 29, 2018 8:02 am
Forum: Other projects
Topic: Simple Word Clock, new Word layout
Replies: 1
Views: 834

Re: Simple Word Clock, new Word layout

Code updated with automatic over night dimming, which adjusts with the month and extra easter eggs.
by bleep42
Mon Jul 16, 2018 5:23 pm
Forum: Other projects
Topic: Simple Word Clock, new Word layout
Replies: 1
Views: 834

Simple Word Clock, new Word layout

IMG_1713.jpg Link to all Images, Videos, Word Docs, and the code. https://www.dropbox.com/sh/fbt3zslpcoiqcxw/AADYVWml-wHzDPpAA25izUw4a?dl=0 I recently found I had an old dusty PiB+ (1CPU 500MB) laying around not doing anything useful, so I decided to build a Word Clock, there seem to be loads of di...
by bleep42
Fri Apr 06, 2018 1:21 pm
Forum: Gaming
Topic: Q3lite - Quake III Arena for the Raspberry Pi
Replies: 118
Views: 72558

Re: Q3lite - Quake III Arena for the Raspberry Pi

Hi John,
Yes I had done the firmware update as well, I just copied and pasted every command in order, till I finished. :-)
I strongly suspect it was caused by the fact that my Stretch was an upgrade from Jessie, not a straight Stretch installation.
Regards, Kevin.
by bleep42
Wed Apr 04, 2018 3:37 pm
Forum: Gaming
Topic: Q3lite - Quake III Arena for the Raspberry Pi
Replies: 118
Views: 72558

Re: Q3lite - Quake III Arena for the Raspberry Pi

Hi, Thanks for your reply, I tried doing all of that, but still exactly the same. So I've reinstalled Raspbian from scratch and that made it work. Thanks. Now is there a way of getting the *. pk3 files from the original Openarena game that you used to be able to download from the RaspberryPi shop to...
by bleep42
Mon Apr 02, 2018 5:35 pm
Forum: Gaming
Topic: Q3lite - Quake III Arena for the Raspberry Pi
Replies: 118
Views: 72558

Re: Q3lite - Quake III Arena for the Raspberry Pi

Hi, I've just tried your latest compile/install procedure as above. Everything appears to compile and install ok, however when I try to run I get an error "...WARNING: could not set the given mode (-2)" I'm using a Pi3B+ Raspbian Stretch and I used the dev branch. crash log below. tty console mode d...
by bleep42
Wed Jan 03, 2018 5:14 pm
Forum: Other projects
Topic: Pi-Portable & or Monitor.
Replies: 72
Views: 52770

Re: 9v really for LCD Driver? Re: Pi-Portable & or Monitor.

I read the manufacturer pdf states 12v for input and this really works stable at 9v? Connecting the output of the input power 9v to the dc in jack should work also, correct? Thank you for your effort in documenting this. Hi, Yes, certainly my board works fine at 9v, it even still worked at 7v, but ...
by bleep42
Thu Aug 31, 2017 6:21 pm
Forum: Troubleshooting
Topic: SD Card permanently locked
Replies: 13
Views: 6584

Re: SD Card permanently locked

Thanks Mahjongg, I'll have a read of the link, however one of the cards was almost new, so unlikely to be warn out. Everything was perfect on the second card until I used Win32DiskImager to read an image file, this is on a PC, not the Pi. Then as soon as I plugged it back into my Pi, it was locked. ...

Go to advanced search