Go to advanced search

by thuranga
Wed Mar 16, 2016 12:32 pm
Forum: Camera board
Topic: How can I identify the module type without connecting?
Replies: 2
Views: 407

Re: How can I identify the module type without connecting?

Thank you for your quick reply! :D
by thuranga
Wed Mar 16, 2016 12:23 pm
Forum: Camera board
Topic: How can I identify the module type without connecting?
Replies: 2
Views: 407

How can I identify the module type without connecting?

Hi,
I have two camera boards. How can I identify which of them is a NOIR-module and which is a "normal" module without connecting them to the Pi? Is there a special ID oder serial number at the module?

Greetings
Thuranga
by thuranga
Mon Jun 22, 2015 11:03 am
Forum: HATs and other add-ons
Topic: Turn off PCD8544 Display
Replies: 2
Views: 545

Re: Turn off PCD8544 Display

Thanks for your answer! I will check it out :)
by thuranga
Thu Jun 18, 2015 1:49 pm
Forum: HATs and other add-ons
Topic: Turn off PCD8544 Display
Replies: 2
Views: 545

Turn off PCD8544 Display

Hi,
has anyone a solution to turn off the PCD8544 display by software?

Greetings
thuranga
by thuranga
Sat Mar 14, 2015 5:47 pm
Forum: Networking and servers
Topic: [SOLVED] Raspberry as Access Point (Hotspot) AND Client
Replies: 5
Views: 1389

[SOLVED] Using Raspberry as Access Point (Hotspot) AND Clien

Wow! You are great!!! # ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP ...
by thuranga
Sat Mar 14, 2015 4:43 pm
Forum: Networking and servers
Topic: [SOLVED] Raspberry as Access Point (Hotspot) AND Client
Replies: 5
Views: 1389

[SOLVED] Raspberry as Access Point (Hotspot) AND Client

Hi, I set up my Pi successful as an access point. Everything works fine. Here is my /etc/network/interfaces : auto lo iface lo inet loopback auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.178.220 netmask 255.255.255.0 gateway 192.168.178.1 auto wlan0 allow-hotplug wlan0 iface wl...
by thuranga
Sat Jan 03, 2015 11:22 pm
Forum: Camera board
Topic: MMAL Motion - tuning & optimisations
Replies: 161
Views: 113623

Re: MMAL Motion - tuning & optimisations

Thanks for your replies! The best frame rate is with video mode (turn mmalcam_use_still to off) using the secondary buffer mechanism to capture a high-res image for recording while performing motion detection on the lower resolution primary buffer I tried this mechanism with 15 frames successfully, ...
by thuranga
Fri Jan 02, 2015 12:20 pm
Forum: Camera board
Topic: MMAL Motion - tuning & optimisations
Replies: 161
Views: 113623

Re: MMAL Motion - tuning & optimisations

Hi,
I have a limitation of only 2 frames/sec when using "mmalcam_use_still on". It does not matter what resolution I set. I want a wider field of view, so I use the still images. Is there a possibility to tune the config for a higher framerate?

Greetings
Thuranga

Go to advanced search