The Raspberry Pi UARTs
The SoCs used on the Raspberry Pis have two built-in UARTs, a PL011 and a mini UART. They are implemented using different hardware blocks, so they have slightly different characteristics. However, both are 3.3V devices, which means extra care must be taken when connecting up to an RS232 or other system that utilises different voltage levels. An adapter must be used to convert the voltage levels between the two protocols. Alternatively, 3.3V USB UART adapters can be purchased for very low prices.
By default, on Raspberry Pis equipped with the wireless/Bluetooth module (Raspberry Pi 3 and Raspberry Pi Zero W), the PL011 UART is connected to the Bluetooth module, while the mini UART is used as the primary UART and will have a Linux console on it. On all other models, the PL011 is used as the primary UART.
In Linux device terms, by default, /dev/ttyS0 refers to the mini UART, and /dev/ttyAMA0 refers to the PL011. The primary UART is the one assigned to the Linux console, which depends on the Raspberry Pi model as described above. There are also symlinks: /dev/serial0, which always refers to the primary UART (if enabled), and /dev/serial1, which similarly always refers to the secondary UART (if enabled).
Mini UART and CPU core frequency
The baud rate of the mini UART is linked to the core frequency of the VPU on the VC4 GPU. This means that, as the VPU frequency governor varies the core frequency, the baud rate of the UART also changes. This makes the UART of limited use in the default state. By default, if the mini UART is selected for use as the primary UART, it will be disabled. To enable it, add
enable_uart=1 to config.txt. This will also fix the core frequency to 250MHz (unless
force_turbo is set, when it will be fixed to the VPU turbo frequency). When the mini UART is not the primary UART, for example you are using it to connect to the Bluetooth controller, you must add
core_freq=250 to config.txt, otherwise the mini UART will not work.
The default value of the
enable_uart flag depends on the actual roles of the UARTs, so that if ttyAMA0 is assigned to the Bluetooth module,
enable_uart defaults to 0. If the mini UART is assigned to the Bluetooth module, then
enable_uart defaults to 1. Note that if the UARTs are reassigned using a Device Tree Overlay (see below),
enable_uart defaults will still obey this rule.
Disabling Linux's use of console UART
In a default install of Raspbian, the primary UART (serial0) is assigned to the Linux console. Using the serial port for other purposes requires this default behaviour to be changed. On startup,
systemd checks the Linux kernel command line for any console entries, and will use the console defined therein. To stop this behaviour, the serial console setting needs to be removed from command line.
This can be done by using the raspi-config utility, or manually.
Select option 5, Interfacing options, then option P6, Serial, and select No. Exit raspi-config.
To manually change the settings, edit the kernel command line with
sudo nano /boot/cmdline.txt. Find the console entry that refers to the serial0 device, and remove it, including the baud rate setting. It will look something like
console=serial0,115200. Make sure the rest of the line remains the same, as errors in this configuration can stop the Raspberry Pi from booting.
Reboot the Raspberry Pi for the change to take effect.
UART output on GPIO pins
By default, the UART transmit and receive pins are on GPIO 14 and GPIO 15 respectively, which are pins 8 and 10 on the GPIO header.
UARTs and Device Tree
pi3-disable-bt disables the Bluetooth device and restores UART0/ttyAMA0 to GPIOs 14 and 15. It is also necessary to disable the system service that initialises the modem so it doesn't use the UART:
sudo systemctl disable hciuart.
pi3-miniuart-bt switches the Raspberry Pi 3 and Raspberry Pi Zero W Bluetooth function to use the mini UART (ttyS0), and restores UART0/ttyAMA0 to GPIOs 14 and 15. Note that this may reduce the maximum usable baudrate (see mini UART limitations below). It is also necessary to edit /lib/systemd/system/hciuart.service and replace ttyAMA0 with ttyS0, unless you have a system with udev rules that create /dev/serial0 and /dev/serial1. In this case, use /dev/serial1 instead because it will always be correct. If cmdline.txt uses the alias serial0 to refer to the user-accessible port, the firmware will replace it with the appropriate port whether or not this overlay is used.
There are other UART-specific overlays in the folder. Refer to
/boot/overlays/README for details on Device Tree Overlays, or run
dtoverlay -h overlay-name for descriptions and usage information.
For full instructions on how to use Device Tree Overlays see this page. In brief, add a line to the
config.txt file to enable Device Tree Overlays. Note that the
-overlay.dts part of the filename is removed.
... dtoverlay=pi3-disable-bt ...
Relevant differences between PL011 and mini UART
The mini UART has smaller FIFOs. Combined with the lack of flow control, this makes it more prone to losing characters at higher baudrates. It is also generally less capable than the PL011, mainly due to its baud rate link to the VPU clock speed.
The particular deficiencies of the mini UART compared to the PL011 are :
- No break detection
- No framing errors detection
- No parity bit
- No receive timeout interrupt
- No DCD, DSR, DTR or RI signals
Further documentation on the mini UART can be found in the SoC peripherals document here.