We've got offices!

7th of February 2013 by liz
submit to reddit

You probably didn’t realise this, but up until now, we haven’t had an office to work from. We’ve been completely virtual: I work from the study at home, we’ve got some space at the University Computer Laboratory in Cambridge which we use for meetings with visitors, there’s a small electronics lab in our house, Jack deals with paperwork from an office in his house, we borrow space at St John’s College for board meetings…it’s not a very efficient way to run a million-unit computer company.

Now we’ve started taking on our first employees, it’s really not a tenable way to do things any more, so Rob Bishop (evangelist and developer), Gordon Hollingworth (GSH on the forums) and James Adams (software and hardware chaps respectively) have been moving into our new office in the centre of Cambridge this week. Clive Beale, Eben and I will be joining them when Clive’s teaching contract is up at the end of the month, and when Eben and I get back from a series of meetings in the US.

We finally have something to keep Rob in. (The chap on the right is from the removals company, and not a Pi person.)

Rob and James Adams survey the mess. Rather them than me; there’s nothing worse in the world than the sound of squeaky polystyrene. Gordon’s behind the camera.

We’ll be decorating soon, but it’s already a fully functional office (we’ve got an entry phone and everything), and best of all, it’s only a few hundred yards from the pub. It’s leafy, it’s central and I’m really looking forward to moving in next week!

 

Buy a Pi!

buyapi

buypiswag
News Archives

Supported by


In the forums
  • pluggy, 54 seconds ago: CSI camera module • Re: Horizontal lines with video, not stills
    You power supply might not be up to the mark, the camera consumes a lot of current, a power supply on the edge can work with stills, but not with video. Testing the voltage across TP1 and TP2 when the…
  • Ravenous, 1 minute ago: Automation, sensing and robotics • Re: After-school Robot Primary Club
    CD wheel adapters here:http://www.rapidonline.com/Education/CD ... tors-10536You might find some other stuff here:http://www.rapidonline.com/Education/Sy ... ls-PulleysPROBLEM is, they charge quite a bit for postage unless you go over about 30-40 quid. And the other problem is, if you read through their catalogue…
  • startrek.steve, 1 minute ago: General discussion • Re: Getting started with Electronics
    Yes, I wanted to have a go at this, so whats the bare minimum gear I need to buy for the Pi to say, plug in and light up some LED's?Steve
  • odem, 5 minutes ago: Deutsch • Re: GPIOs immer aktiv
    So, ich hab nochmal alles durchgemessen und es sieht wie folgt aus: Die Spannungen sind weiterhin fix wie sie unten stehen. Einzig der GPIO-Port 27 (mit 0,16V) lies sich jetzt plötzlich ansteuern. Code: GPIO   Spannung (V)2      3,33      3,34 …
  • Tinwarble, 7 minutes ago: General discussion • Re: DTS-MA passthrough
    Jessie wrote:Canned responses from OUYA. Yes there is a non-point there because none of these devices can't pass-through they are all capable it is all a matter of software. So as of right now you should most likely be petitioning…

On Twitter
  • asbradbury, 5 hours ago
    Pekka Paalanen has written a great technical blog post about implementation of the new Weston @Raspberry_Pi backend http://t.co/PIIJJa6rzE Cambridge, UK
  • adafruit, 7 hours ago
    How To Disable The Red LED On The Pi Camera Module #piday #raspberrypi @Raspberry_Pi http://t.co/fuUzkC7KYI New York, NY - USA
  • masafumiohta, 7 hours ago
    now 1 ticket available for Non-Japanese registration for our Big Jam in Tokyo check http://t.co/nY5ScK8Mxn CCed: @Raspberry_Pi @TheMagP1 Tokyo
  • TeamRaspi, 19 hours ago
    Very cool car computer by @FlamelilyIT using @Raspberry_Pi - new blog post http://t.co/i1lefiRhUX Cambridge

Friends of Pi